birt code 39

birt code 39

birt code 39

birt code 39

birt code 39

birt code 39,

birt code 39,
birt code 39,

birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,

birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,
birt code 39,

Use different fills for the control object to create different looks in combination with the Emboss effect

.

.

look more detailed, refined, and almost photorealistic in appearance In addition to having an Altitude slider in this mode, you have To Center as an available option in the Bevel Offset field Here s what it does and how To Center works All Soft Edge bevels are produced from the edge of a shape traveling toward its center If, for example, you ve created a circle that s 3" across and then type a Distance offset value in the num box in any amount smaller than 15", you ll see a dimensional, sloping bevel created inside the circle, with a flat top in the shape of the circle in its center If, however, you type in a value greater than 15", the center of the object will bevel to a point, and the front face of the object is entirely lost The reason this happens (you might or might not want this visual effect) is that the Bevel effect travels toward the interior of the shape, and half of the 3" diameter of this circle is 15" Just keep in mind the size of the shape to which you apply a Bevel to gain total control over the effect If, on the other hand, you intend for the sides of the bevel to come to a point, you don t need to set values in the Distance field; you choose To Center, click Apply, and CorelDRAW creates the maximum width bevel, meeting at a point inside the shape You can create interesting marine creatures such as a starfish by using the Polygon Tool to create the silhouette of a starfish, fill the object, and then To Center auto-creates a very lifelike composition Although you can create a To Center bevel by increasing the Distance setting, it s not only much simpler to use the To Center option, but also less confusing You can, for example, specify a 4" Distance in the Offset field to apply to a 1" object, but CorelDRAW limits the line to ", even though you can enter such a mathematically impossible value in this field Figure 23-3 shows two very different looks for the Bevel effect: at top a Distance has been set for the Offset, and at bottom To Center is chosen.